Rheology Modifier Clays
BS-1C-FF is an organo-clay for solvent-based systems of low to medium polarity.
Advantages
- High gelling efficiency over low and medium polarity organic liquids
- High viscosity and excellent thickening property over a wide temperature range.
- Imparts particle suspension, preventing hard settling of pigment and fillers.
- Ideal thixotropy property and anti-sediment property.
- Exerts strong film reinforce action in organic binder systems
Typical Properties
| Color | Appearance | Density | Moisture (@105℃,2hrs) | Mesh Size (200 mesh) | Loss on Ignition (@1000℃) |
|---|---|---|---|---|---|
| Light Yellow | Free Flowing Powder | 1.75g/cm3 | ≤3.5% | ≥97% | ≤33.0% |
Typical Applications
- Adhesives and Sealants
- Anti-Corrosion Paints
- Container Paints
- Bituminous Paints
- Printing inks
- Lubricating grease
Usage
BS-1C-FF belongs to the conventional type of organo-clay group, which requires mechanical energy, shear forces applied with a good dispersion equipment, and a chemical (polar) activator to reach the proper level of delamination of the organo-clay particles.
Polar Activator: Dosage of polar activator (such as 95%ethanol, 95%methanol, 95%acetone or propylene carbonate) is 30%-50% by weight of BS-1C-FF.
It is always recommended to determine the proper level of addition by experiment. Either defect or excess of chemical activator would result in poorer viscosity development.
Recommended Levels
The amount of BS-1C-FF rheology modifier required depends upon the type of organic system and the degree of thickening or other properties desired. Addition levels are typically between 0.50-2.0percent by weight of the total system.
International Countertypes
Bentone®38、Bentone®-34、Claytone®-40
HFGEL-120-A21 Rheology Modifier
HFGEL-120-A21 is an organo-clay for oil-based drilling mud (fluid).
Advantages
- Imparts good dispersion, high gel strength, and stable viscosity properties of oil based drilling fluids.
- Used to gel oil drilling fluids for long-term suspension of weighting agents in drilling and packer fluids.
- Aids in hole cleaning, and improves carrying lithology property.
- Stable at both high and low temperatures.
- Usually preferred in diesel-based, mineral oil-based, synthetic oil-based and modified vegetable oil-based drilling fluids.
Typical Properties
| Color | Appearance | Bulk Density | Moisture (@105℃,2hrs) | Fineness through 200mesh |
|---|---|---|---|---|
| Cream | Free Flowing Powder | ≤480kg/m3 | ≤3.5% | ≥95% |
Typical Applications
- Diesel Based Drilling Fluids and Water in Oil Drilling Fluids.
- Low Aromatic Hydrocarbon Mineral Oil Based Drilling Fluids and Water in Oil Drilling Fluids.
- Synthetic Oil Drilling Fluids and Water in Oil Drilling Fluids.
- Drilling Protecting Fluids, Completion Fluids, Stuck Releasing Fluids.
Usage
Add 25-40kg/m3 of HFGEL-120-A21 to make water in oil drilling fluids, or adjust the quantity based on real situation
Normally the consumption of HFGEL-120-A21 in mineral oil-based, synthetic oil-based and modified vegetable oil-based drilling fluids will be higher than diesel-based drilling fluids.
When making the oil based drilling fluids, adding a small stream of water（0.1-0.5%）will be helpful to get ideal effect.
HFGEL-120-A21needs enough shearing to be well dispersed, to get the required viscosity
BS-1C-HM Rheology Modifier
General Information
BS-1C-HM is a kind of Rheology Modifier that used for diesel-based, white oil-based and synthetic oil-based drilling fluids. The use of BS-1C-HM can change rheological property, suspension property and carrying lithology of oil-based drilling fluids.
It can suspend cuttings and weight materials well in the drilling fluids, which is conductive to prepare highdensity or ultra-high-density oil-based drilling fluids.
It is also favourable for oil-based drilling fluids applied in large displacement wells, horizontal wells, deep wells, ultra-deep wells and other special processes. Also for multiple sets of pressure systems and other complex formation applications.
Using BS-1C-HM in oil-based drilling formula not only can greatly improve the yield value of drilling fluid, but also can improve the viscosity of drilling fluid under low shear force to protect the side wall.
Specifications
| PARAMETER | VALUE |
|---|---|
| Appearance | Light yellow powder |
| Moisture，(105℃)% | ≤3.5 |
| Fineness（-200mesh） | ≥95.0 |
Instructions for Use
BS-1C-HM can be used to increase the yield value and gel strength of diesel base, white base and synthetic oil base. The performance will be better if there is good stirring or sufficient shearing action when using the product. In the use process, BS-1C-HM can be well dispersed in the base oil before adding the main emulsifier and other drilling additives. The addition amount is generally 1.0%-5.0%of the total drilling fluid.
BS-1C-AD Organo-Clay
Introduction
BS-1C-AD is an organo-clay for oil-based drilling mud (fluid)
It can suspend cuttings and weight materials well in the drilling fluids, which is conductive to prepare highdensity or ultra-high-density oil-based drilling fluids.
Advantages
- Impart viscosity and suspension properties to oil-based drilling fluids.
- Used to gel oil drilling fluids for long-term suspension of weighting agents in drilling and packer fluids.
- Aids in filtration control
- Usually preferred in diesel oil based and mineral oil based fluids. Should not be used in high performance clay-free oil based drilling fluids.
Typical Properties
| Color | Appearance | Density | Moisture(@105℃,2hrs) | Fineness through 200 mesh | Loss on Ignition ( @1000℃) | Bulk Density (g/m3) |
|---|---|---|---|---|---|---|
| White | Free Flowing Powder | 1.70g/cm3 | ≤3.5% | ≥95% | ≤35% | 460 |
Typical Applications
- Helps improve viscosity any oil-based drilling fluid
- Helps improve hole cleaning during drilling and work over operations
- Gel oil muds for long-term suspension of weighting agents in packer fluids and casing packs
Usage
Add 1-15lb/bbl (2.86-42.80kg/m3) of BS-1C-AD slowly through the hopper
Note: Decrease yielding time by adding a small stream of water through the hopper at the same time.
BS-1C-HA Rheology Modifier
BS-1C-HA is an organo-clay for oil-based drilling mud (fluid).
Advantages
- Impart viscosity and suspension propertiesto oil-based drilling fluids.
- Used to gel oil drilling fluids for long-term suspension of weighting agents in drilling and packer fluids.
- Aids in filtration control
- Usually preferred in all diesel oil /aromatic mineral oil based and oil-emulsion based fluids. Should not be used in high performance clay-free oil based drilling fluids.
Typical Properties
| Color | Appearance | Density | Moisture(@105℃,2hrs) | Fineness through 200 mesh | Loss on Ignition ( @1000℃) |
|---|---|---|---|---|---|
| White | Free Flowing Powder | 1.70g/cm3 | ≤3.5% | ≥95% | ≤35% |
Typical Applications
- Helps viscosify any oil-based drilling fluid
- Helps improve hole cleaning during drilling and work over operations
- Gel oil muds for long-term suspension of weighting agents in packer fluids and casing packs
Usage
Add 10-30kg/m3 of BS-1C-HA viscosifier slowly through the hopper
Note: Decrease yielding time by adding a small stream of water through the hopper at the same time.
BS-1C-10 Organo-Clay
TIntroduction
BS-1C-10 is a type of economical organo-clay, which has good disperse ability, suspension and pulping properties in oil-based mud. It is generally used as thickener, filtrate loss reducing agent, and stuck release agent.
BS-1C-10 has high gel efficiency, good dispersion and stable viscosity usually preferred in various drilling fluid systems such as diesel oil, mineral oil, and synthetic oil and modified vegetable oil. There is no need to add chemical activator when using it.
BS-1C-10 can also adapt to the low and high temperature
Typical Properties
| Appearance | Bulk Density | Moisture (@105 Deg.C , 2hrs) | Sieve residue 200 mesh |
|---|---|---|---|
| Off-white powder | ≤480kg/m3 | ≤3.5% | ≤5% |
Applications
- Diesel-based drilling fluid and water-in-oil drilling fluids
- Low aromatic hydrocarbon oil (white oil) based drilling fluid and water-in-oil drilling fluids
- Synthetic oil based drilling fluid and water-in-oil drilling fluids
- Drilling Protecting Fluids, Completion Fluids, Stuck Releasing Fluids
Advantages
- Forms a gelled structure in the base oil to adjust the adhesiveness of the drilling fluid
- Improves hole cleaning and the ability of carrying sand
- Improves quality of mud cake and reduce water loss of mud
- Increases suspension of oil-based drilling fluid, suspending weighted materials
Usage
Add 25-40kg/m3 of BS-1C-10 to make water in oil drilling fluids, or adjust the quantity based on needs
Normally the consumption of BS-1C-10 in mineral oil-based, synthetic oil-based and modified vegetable oil- based drilling fluids will be higher than diesel-based drilling fluids.
When making the oil based drilling fluids, adding a small stream of water（0.1-0.5%) will be much helpful to get ideal effect.
BS-1C-10 needs enough shearing to be well dispersed, to get the required initial viscosity.
FH-8002C Water Treatment Flocculant
FH-8002C is the upgraded version of FH-8002A. Main ingredients of FH-8002C are polymers, clays, inorganic salts.
Typical Applications
- Oil Waste Water
- Water Based Paints
- Water Based Inks
- Color Paste
- Glass Cutting Fluid
- Printing & Dying
- Adhesive
- Metal Smelting
- Paper Making
Method of Use
- Add 0.05g FH-8002C to 100ml waste water
- Stir for 1minute, and mix the materials uniformly.
- Wait for 5minutes and observe the clarity.
- If the performance is not satisfactory, add more 0.05g FH-8002C, and repeat above process.
Performance
- COD removing rate is 50%-99%.
- Ammonia-Nitrogen removing rate is 15%
FH-8002A Water Treatment Flocculant
Main ingredients of FH-8002A are polymers, clays, inorganic salts.
Operation Method
- Add 0.05g FH-8002A to 100ml waste water.
- Stir for 1minute, and mix the materials uniformly.
- Wait for 5minutes and observe the clarity.
- If the performance is not satisfactory, add more 0.05g FH-8002A, and repeat above process.
Typical Applications
- Oil Waste Water
- Water Based Paints
- Water Based Inks
- Color Paste
- Printing & Dying
- Adhesive
- Metal Smelting
- Paper Making
Performance
- COD removing rate is 50%-99%.
- Ammonia-Nitrogen removing rate is 15%
Packing: 25 kg. poly lined paper/HDPE bags / 500 kg. Jumbo Bags.
Specifications
Specifications
| PARAMETER | VALUE |
|---|---|
| Appearance | Light yellow powder |
| Moisture，(105℃)% | ≤3.5 |
| Fineness（-200mesh） | ≥95.0 |